Meade DB1 InstMnl 061303.qxd 6/23/03 2:03 PM Page 1
Operating Instructions
TM
Meade® 8 x 22 VGA CaptureView
Integrated Binocular and Digital Camera
WARNING! Never use a Meade® binocular to look at the Sun!
Looking at or near the Sun will cause instant and irreversible
damage to your eye. Eye damage is often painless, so there is no
warning to the observer that damage has occurred until it is too late.
Do not point the binocular at or near the Sun. Children should
always have adult supervision while observing.
Fig. 1:Top View
f
g
f
g
1. Eyepieces
2. Mode Button
3. Shutter Button
4. LCD Panel
5. Objective Lens
6. Barrel
e
Fig. 2: Front View
7. Camera Lens
c
d
h
b
Page 1
Meade DB1 InstMnl 061303.qxd 6/23/03 2:03 PM Page 3
II. How to Use Your Binocular
To enhance your viewing enjoyment, please take a moment to familiarize
yourself with your new binocular:
Adjustment of Eye Relief for Eyeglass Wearers
For best results when viewing an object while wearing eyeglasses, fold down
the rubber eyecups and place them against your glasses.
Adjusting the Eyepieces
The distance between your eyes is usually different than the distance between
another person’s eyes. This distance is known as the interpupillary distance, or
IPD. Adjustment to your IPD is important to the proper use of your
CaptureView:
1. Hold CaptureView up to your face in the normal viewing position using both
hands to hold each barrel firmly.
2. Pull the barrels apart or push the barrels together until you see a single
circular field with both of your eyes.
Focusing the Binocular
1. Set the Diopter Scale on underside of CaptureView (9, Fig. 3) at its center
point between + and -.
2. Choose an object that is at least 50 feet (15m.) away.
3. Looking with just your left eye, rotate the Center Focus Knob (10, Fig. 3)
until the object you are viewing is in best focus.
4. Looking with just your right eye, rotate the Diopter Scale (9, Fig.3) until the
object you are viewing is in best focus.
5. Now, looking with both eyes, with a turn of the Center Focus Knob both far
and near objects can easily be brought into focus.
III. How To Use Your Camera
CaptureView performs best under good lighting conditions. It takes some
practice to get used to high-magnification photography. Take some time to
practice capturing still pictures and movies. Depending on the available light
and your distance from the object, captured images may not appear as bright
or centered exactly as viewed through the binoculars. Note also that
CaptureView has a fixed focus (you cannot focus the camera manually) and
takes focused pictures even if the image in the binoculars is out-of-focus.
Inserting Batteries
1. Push the battery compartment lid (11, Fig. 3) forward and lift to open.
Page 3
Meade DB1 InstMnl 061303.qxd 6/23/03 2:03 PM Page 4
2. Insert 2 AAA 1.5v (user-supplied) batteries into the compartment, noting the
correct polarity as illustrated inside the compartment.
Choosing an Operation
Press and hold the Mode button (2, Fig. 1) for 3 to 5 seconds to turn on the
camera. Press the Mode button to display the operation icons on the LCD.
When the desired icon is displayed, press the Shutter button (3, Fig. 1) to
select that operation. The following example demonstrates how to use these
buttons. See Part IV, Operation, for a description of the operations.
Taking Pictures and Movies
1. Press and hold down the Mode button for 3 to 5 seconds to turn on the
camera. The camera will beep and the camera icon displays on the LCD.
The counter, battery life, and resolution icons also display.
2. Point the binoculars at an object. You may use the focus knob to focus the
image in the binocular, but keep in mind that the camera has a fixed focus
and is not affected by the focus knob.
3. Press the Shutter button. Note that the counter has advanced to "001." You
have now taken your first picture.
4. Press the Mode button once and the Video mode icon displays.
5. Point the binoculars at the scene you wish to film. Press the Shutter button.
The camera now captures a movie . Note that the counter keeps counting as
you film. Press the Shutter button again to stop recording the movie. Note
that the counter stops.
6. You can change the resolution of the pictures you capture. The first time
you turn on the camera, it displays the High Resolution icon. This is the
default mode. To change the resolution, keep pressing the Mode button until
the Low Resolution icon displays. Then press the Shutter button to select
Low Resolution. Low resolution allows you to capture more images with
your camera.
7. Press and hold down the Mode button for 3 to 5 seconds to turn off the
camera. If you do not perform an operation for 30 seconds, the camera
switches to sleep mode. Press Mode to "wake up" the camera. If you wish to
download your pictures, see Part VI, Downloading and Software installation.
To sum up: Use the Mode button to cycle through the operation icons. Then
press the Shutter button to select the displayed operation. Also, use the Shutter
button to take a picture and to begin or end the recording of a movie.
As you press the Mode button, the operation icons display on-screen in the
following order: Camera, Video , Resolution, Compression, Selftimer, Erase
Last Image, and Erase All Images. The next press returns you to Camera.
Page 4
Meade DB1 InstMnl 061303.qxd 6/23/03 2:03 PM Page 5
IV. Operation
Camera
Keep pressing the Mode button until the Camera icon displays. Then
press the Shutter button to take a still picture. Remember to select a
Resolution setting before taking a still image (see below). If you
take more than 999 pictures, the camera counter returns to 001. The
camera icon flashes, indicating that the number of pictures is 999
plus the number displayed on the counter.
Video mode.
Keep pressing the Mode button until the Video icon displays. Then
press the Shutter button to begin recording a movie. Press the
Shutter button again to stop recording. The length of a movie depends
on how much memory you have available. Note: Audio recording is
not available with this camera.
Erasing/Deleting Pictures
Erase Last. Display the Erase Last Image icon and press the Mode
button. The icon flashes. Press the Mode button again to erase the
last captured image or movie.
Erase All. Display the Delete All Images icon and press the Mode
button. The icon flashes. Press the Mode button again to erase all
the images and movies.
Resolution Options
CaptureView provides two Resolution settings: High and Low.
You can take more pictures in the Low Quality mode than in the
High Quality mode. Keep pressing the Mode button until the Quality
mode icon displays. Then press the Shutter button to change the
resolution.
H: High Resolution mode (640 x 480). Default.
* *
*
L: Low Resolution mode (320 x 260).
LCD Counter
Displays the number of pictures or movies taken, from 0 to 999.
Selftimer
Keep pressing the Mode button until the Selftimer icon displays and
press the Shutter button. The camera then pauses: It sends out 6
slow and then 6 fast warning beeps before taking the picture.
Page 5
Meade DB1 InstMnl 061303.qxd 6/23/03 2:03 PM Page 6
Battery Life.
Battery Good/Battery Low indicators.
Buzzer Alerts
Power on: Two short high beeps.
Wake up: One long high beep.
Sleep: One short high beep.
Takes a picture: One short high beep.
Low battery: Six short high beeps (beeps only when power is On).
Failed to take picture due to insufficient light or memory: Three short
high beeps
SelfTimer: When selected, sends out 6 slow, then 6 fast beeps before
taking a picture.
V. System Requirements
1. Windows 98/Win Me/Win 2000/Win XP
2. 200MHz (or equivalent) processor or faster.
3. 64MB of RAM free over System requirements
4. Video (VGA) card with 2MB of RAM for minimum 16-bit (High Color)
display.
5. 4x CD-ROM drive.
6. USB port (1.1).
7. 600MB of free hard drive space.
If you have questions regarding your PC system specifications, please contact
your PC manufacturer.
VI. Downloading and Software Installation
Driver Installation
Note: DirectX 8.1 or higher must be installed on your PC before you can
download images. If you do not have DirectX 8.1 or higher on your PC,
DirectX 8.1 is included on the CD ROM. To install, click the "Install DirectX"
button on the CD ROM.
1. Install the software first. Do not plug your camera in until step #5.
2. Insert the provided CD ROM into your CD ROM drive.
3. The CaptureView Manager menu displays. Click on the "CaptureView VGA
Manager."
Page 6
Meade DB1 InstMnl 061303.qxd 6/23/03 2:03 PM Page 7
Note: Only click on the "CaptureView VGA Manager" button; do not click on
any of the other CaptureView Manager buttons.
4. The driver setup begins. Follow the on-screen directions. Note that if a
window displays a choice of buttons to "Continue Anyway" or "Stop
Installation," click on "Continue Anyway."
5. After the setup is complete, follow any on-screen instruction (e.g., "Restart
Computer"). Using the provided USB cable, plug the one end of the cable
into the camera's USB port and the other end into your PC's USB port.
Refer to Fig. 5.
6. Wait for about 10 seconds, follow any on-screen instructions. You may now
download images to your PC using the CaptureView Manager.
7. Click on the "CaptureView Manager Manual" button to display the on-screen
instruction manual for the CaptureView Manager software.
Other Software
The CD ROM also includes other software programs by Ulead that will assist
you in editing your images, allow you to transfer images to email, and provide
®
you with other useful functions. Ulead Photo Express , Photo Explorer, and
™
Cool 360 , and CaptureView Manager are proprietary programs, and may not
be sold, licensed or distributed without the express written consent of Ulead. or
more information about Ulead Photo Express, visit the Ulead website at
section of their homepage to find a link for the Photo Express manual.
Fig. 5: Connecting CaptureView to a PC
Page 7
Meade DB1 InstMnl 061303.qxd 6/23/03 2:03 PM Page 8
Troubleshooting
It is very important to use the following connection and disconnection
procedures to download pictures.
1. Only connect CaptureView to your PC when the PC is on and Windows has
completed loading.
2. Your CaptureView camera and PC must be connected before running the
CaptureView Manager program.
3. Avoid physically connecting, disconnecting and reconnecting the camera
during a download session. Instead, disconnect the camera using Windows
software: Right-click the USB on-screen icon and select disconnect (or
connect to reconnect).
4. Always disconnect CaptureView before shutting down the PC.
If CaptureView is unexpectedly not recognized by the software program, close
the program, disconnect the camera and reboot your PC. Only connect and
disconnect your CaptureView using the procedure outlined in this section.
VII. Maintenance
Operating Environment: 41° to 104° F (5° to 40° C). 20%-85% relative
humidity, non-condensing.
Care of your CaptureView
1. Never immerse CaptureView into any fluid or liquid. Remove dust or
stains with a soft cloth dampened with water or neutral detergent. Keep in a
dry and cool dust-free environment or a container when it is NOT used.
Do not spray liquid cleaners directly onto LCD. Using only gentle pressure,
wipe the LCD with a slightly dampened cleaning cloth.
2. Take the batteries out when CaptureView is NOT to be used over a long
period.
3. Avoid dropping the CaptureView. Do not disassemble CaptureView.
4. Download pictures to your PC before removing the batteries.
Note: After taking out the batteries, power to the CaptureView will be
maintained for 90 seconds. Batteries must be replaced within 60 to 90
seconds to avoid loss of pictures. Be sure the CaptureView is off before
changing the batteries.
Page 8
Meade DB1 InstMnl 061303.qxd 6/23/03 2:03 PM Page 9
VIII. Specifications
Binocular power
8X
Binocular objective lens diameter
Binocular optical design
Binocular close focus
Field of view (diagonal)
Binocular field of view
Image capture resolution
Max length of movie
22mm
Folding roof prism, fully-coated
16 ft.
7.2°
382 ft. at 1000 yds.
640 x 480, 320 x 260, 24-bit color
Up to 200 seconds
f/4.0; fixed lens
Camera aperture
Camera optimum range
Memory
49 ft. to infinity
16MB SDRAM
Storage capacity at each resolution
640 x 480: 400 images
320 x 260: 1600 images
Windows 98/2000/Me/XP
USB
Operating system requirements
Interface type
Display
LCD
Weight
9.7 oz. (276g)
Product dimensions
Batteries (user supplied)
Accessories
4.75" W x 2.4" H x 4.25" D
Two x AAA 1.5V alkaline
USB cable, instructions, neck
strap, cleaning cloth, carry case,
CD ROM with image editing
software
Page 9
Meade DB1 InstMnl 061303.qxd 6/23/03 2:03 PM Page 10
MEADE BINOCULAR/DIGITAL CAMERA LIMITED WARRANTY
Every Meade binocular/digital camera is warranted by Meade Instruments Corporation (“Meade”)
to be free of defects in materials and workmanship for a period of ONE YEAR from the date of
original purchase in the U.S.A. and Canada. At its option, Meade will repair or replace the product,
or part thereof, found upon inspection by Meade to be defective, provided the defective part or
product is returned to Meade, freight prepaid, with proof of purchase. This warranty applies to the
original purchaser only and is non-transferable. Meade products purchased outside North
America are not included in this warranty, but are covered under separate warranties issued by
Meade International Distributors.
RGA Number Required: Prior to the return of any product or part, a Return Goods Authorization
(RGA) number must be obtained from Meade by writing, or by calling Meade Customer Service at
(800) 62-MEADE. Each returned part or product must include a written statement detailing the
nature of the claimed defect, as well as the owner’s name, address, and phone number.
This warranty is not valid in cases where the product has been abused or mishandled, where
unauthorized repairs have been attempted or performed, or where depreciation of the product is
due to normal wear-and tear. Meade specifically disclaims special, indirect, or consequential dam-
ages or lost profit, which may result from a breach of this warranty. Any implied warranties which
cannot be disclaimed are hereby limited to a term of one year from the date of original retail pur-
chase.
This warranty gives you specific rights.You may have other rights which vary from state to state.
Meade reserves the right to change product specifications or to discontinue productions without
prior notice. This warranty supersedes all previous Meade binocular warranties.
ANY RETURN MADE IN THE U.S.A. UNDER THIS LIMITED WARRANTY MUST FOLLOW THIS PRO-
CEDURE:
1.
2.
Carefully package your binocular/digital camera to avoid shipping damage; use
a thick-walled carton box for mailing.
Enclose a written statement detailing the exact nature of the service needed. Be
sure to include the RGA number, your name, address, plus daytime and evening
telephone numbers.
3.
4.
Enclose $10.00 to cover handling and return-shipping, by check or money order
payable to “Meade Instruments.” Non-warranty repairs may entail additional
charges which will be confirmed with you before any binocular/digital camera
repairs are initiated.
Insure the package and send your binocular/digital camera, freight prepaid, to:
Meade Instruments Corporation,
Attn: Binocular/Digital Camera Repair
6001 Oak Canyon, Irvine, California 92618
® The name “Meade,” and the Meade logo, are trademarks registered with the U.S. Patent Office
and in principal countries throughout the world. All rights reserved.
© 2003 Meade Instruments Corporation.
A D V A N C E D P R O D U C T S D I V I S I O N
Meade Instruments Corporation
World’s Leading Manufacturer of Telescopes for the Serious Amateur
6001 Oak Canyon, Irvine, California 92618 I (949) 451-1450
14-8900-01 v. 6/03
|