B. The unit has been exposed to rain.
C. The unit has been dropped or the enclosure damaged.
D. The unit exhibits a marked change in performance or does not operate normally.
12. Servicing
The user should not attempt to service the unit beyond those methods described in the user's
operating instructions. Service methods not covered in the operating instructions should be
referred to qualified service personnel.
Care and Maintenance
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Do not subject the unit to excessive force, shock, dust or extreme temperature.
Do not tamper the internal components of the unit.
Clean your unit with a damp (never wet) cloth. Solvent or detergent should never be used.
Avoid leaving your unit in direct sunlight or in hot, humid or dusty places.
Keep your unit away from heating appliances and sources of electrical noise such as
fluorescent lamps or motors.
Resetting the unit
If the unit experiences a power surge or electric shock, it is possible that the internal micro-
controller may lock up and the unit will not respond to any commands from the panel controls.
1. In this event, unplug and then reconnect the AC mains power plug into the wall outlet.
2. Use a straightened paper clip, toothpick or similar objects to press the RESET button located
at the rear of the main unit (see the below figure).
Caution: Do not use a sharp, pointed object to press the reset button. It may damage the
reset switch inside the unit.
Features
Thank you for purchasing the BT-125 - 3D sound speaker with Bluetooth®.
This model incorporates following features:
-
Playback mobile device, like Apple devices, smart phones or tablet music through Bluetooth®
technology
-
-
-
NFC (Near Field Communication) function for easy Bluetooth® connection
Audio line-in (AUX) for connecting other digital audio player
Built-in 6 High Fidelity Speakers and incorporated wave field synthesis (WFS) technology to
produce 3D sound effect
-
-
Built-in subwoofer for heavy bass effect
USB connector for charging smart phone battery.
iPhone, iPod, iPod mini, iPod nano, iPod touch, iPod classic and iPod shuffle are trademarks of
Apple Inc., registered in the U.S. and other countries.
3
Apple devices like iPad/iPhone/iPod, smart phones and/or tablet are not included.
Description of parts
Front View
Rear View
1. Six wave field synthesis (WFS) speakers
2. NFC sensor
The NFC (Near Field Communication) sensor located at middle top
of the unit.
®
3. FUNC. button
The function button, press to select Bluetooth or AUX-IN mode.
4. VOLUME + / - button
Adjust volume level up or down.
Turn the unit on or off.
5. POWER
button
6. Status LED indicator
7. AC socket
Power supply to the unit.
8. USB connector
Power source DC 5V (1000mA) for charging mobile device battery
only.
9. AUX-IN jack
Auxiliary audio signal input.
®
10. PAIRING button
11. RESET button
12. Subwoofer
Press to enter Bluetooth pairing mode.
For resetting the unit.
13. Bass Reflex Opening
This opening should never be blocked otherwise the bass effect
will be reduced.
Installation
AC Power Connection
(1) Connect the power cord plug to the AC socket located at rear of the unit.
(2) Firmly and securely plug the AC mains plug into AC mains outlet.
Bluetooth® operation
4
The unit plays from mobile devices (like, iPad/iPhone/iPod Touch ,Smart phone and tablet) music
through Bluetooth® operation. It also incorporated NFC (Near Field Communication) function for
easy connection with a mobile device which also has the NFC function.
(A) NFC Bluetooth® pairing / connection
1.
2.
Press the POWER
button to turn on the unit.
Press the FUNC (function) button to select Bluetooth® mode, where the blue Status LED
indicator blinks fast.
3.
4.
Unlock the mobile device then place it (incorporated NFC function) on top of the NFC
sensor area.
The mobile device will pair and connect with this model automatically.
Note: The Bluetooth® device name of this model: Lenco
5.
6.
After successful connection, the blue Status LED indicator will light steadily.
Now you can playback Bluetooth® music, see section “Playback Bluetooth® music” below.
(B) Manual Bluetooth® pairing/connection
1. Press the POWER
button to turn on the unit.
2. Press the FUNC button to select Bluetooth® mode. The blue Status LED indicator will blink
fast whilst the unit is searching nearby Bluetooth® device.
3. From the mobile device, turn on its Bluetooth® function and it will also search for the nearby
Bluetooth® device as well.
4. From the Bluetooth® device list of your mobile device, tap on Bluetooth® device name
“Lenco” of this model for the connection.
5. Once the mobile device is connected with the unit, the blue Status LED indicator light steadily.
6. Now you can playback Bluetooth® music, see section “Playback Bluetooth® music” below.
(C) Bluetooth® pair / connect other mobile device
In case you would like to pair/connect other mobile device:
1. Press the PAIRING button which located at rear of the unit and enter the pairing mode.
2. It will search nearby Bluetooth® device and the blue Status LED indicator blinks fast.
3. Turn on the mobile device’s Bluetooth® function and select the Bluetooth® device “Lenco” for
the connection.
4. After the successful connection, the blue Status LED indicator will light steadily.
5. Now you can playback Bluetooth® music, see section “Playback Bluetooth® music” below.
Playback Bluetooth® music
1. After Bluetooth® communication link is set up, run the music player App from the mobile
device then playback the mobile device music.
2. You may adjust both the volume control of your mobile device and the volume control of this
unit to find the most desirable volume setting.
3. From the mobile device, you may press:
(a) the
(b) the
/
button to Play / Pause Bluetooth® music.
/
button to skip tracks forward / backward.
5
Note:
Whilst the blue Status LED indicator blinks (3 minutes) fast, the unit is searching mobile device
for pairing.
Whilst the blue Status LED indicator blinks slowly, it means that the Bluetooth® communication
disconnected or after the 1st three searching minutes. To establish the Bluetooth® connection,
implement the 3 approaches (A), (B) or (C) mentioned in above sections.
Energy Saving Note
In Bluetooth® mode, if the Bluetooth® communication link disconnected for around 30 minutes,
the unit will go into standby mode automatically.
Listening to an external audio source
1. Connect an audio cable with 3.5mm stereo plug from an auxiliary audio device to the AUX-IN
jack of the unit.
2. Press the POWER
button to turn on the unit.
3. To select auxiliary audio input, press the FUNC button and the green status LED indicator will
blink for around 5 seconds then lights steadily.
4. Turn on the external auxiliary audio device.
5. The volume can now be controlled through the unit.
Operate all other functions on the external device as usual.
Notes: (a) Press the POWER
button to turn off the unit when you finish listening.
Don't forget to switch off the power of the external audio device as well.
(b) If there is without any music (signal) presented at the AUX-IN input jack for around 10
minutes, the unit will turn into standby mode automatically.
Charging smart phone/mobile device battery
The unit incorporated an USB port with DC 5V (1000mA Max.) output which provides a way for
you to charge mobile device’s battery.
You can connect a mobile device like Apple devices, smart phones or tablet to the USB
connector of the unit. Once the AC mains power is connected and it will charge the mobile device
battery.
3D Sound effect
This model integrated sonic emotion 3D sound technology which uses (WFS) wave field
synthesis to create the illusion of sounds all around. Any input even stereo can be used including
the iPhone/iPad/iPod Touch/Smart phone Bluetooth® streaming music or Aux-in music being in
stereo; by using WFS from sonic emotion, the 3D sound effect can create a virtual sound field
where you can enjoy the finest audio no matter where you are in the room from a single device.
Sonic emotion and Sonic Emotion 3D sound are registered trademarks of sonic emotion ag.
thDe ownload from Www.Somanuals.com. All Manuals Search And Download.
6
Technical Data
Power Supply for the unit
USB connector
AC 100 - 240V ~ 50/60Hz
USB power source, output DC 5V (Maximum 1000mA)
(for charging external appropriate mobile device battery)
Speaker Output
Total 15W x 6 + 35W (Max.)
Operating temperature
and Humidity
0 ~ +35 degree C
70%
Service and support
Lenco helpdesk:
Germany
The Netherlands 0900-23553626 (Local charges + 1ct p/min)
Belgium 02-6200115 (Local charges)
0900-1520530
(Local charges)
The helpdesk is accessible from Monday till Friday from 9 AM till 6 PM.
When contacting Lenco, you will always be asked for the model and serial number of your
product. The serial number can be found on the back of the device. Please write down the serial
number below:
Model: BT-125
Serial number:_________________________________
Lenco offers service and warranty in accordance to European law, which means that in case of
repairs (both during and after the warranty period) you should contact your local dealer.
Important note: It is not possible to send products that need repairs to Lenco directly.
Important note:
If this unit is opened or accessed by a non-official service center in any way, the warranty
expires.
This device is not suitable for professional use. In case of professional use, all warranty
obligations of the manufacturer will be voided.
Notice, statements and information
Lenco is not liable for printing errors in the manual.
The specifications and external appearance of the set are subject to change without prior notice.
Declaration of Conformity
7
Products with a CE marking comply with the EMC directive (2004/108/EC) and the
Low Voltage Directive (2006/95/EC) issued by the European Commission of the
European Community.
When you see a crossed-out wheeled waste container on the product, it means that
the product is subject to the EU directive 2002/96/EC.
This symbol indicates that the relevant electrical product or battery should not be
disposed of as general household waste in Europe. To ensure the correct waste
treatment of the product and battery, please dispose them in accordance to any applicable local
laws of requirement for disposal of electrical equipment or batteries. By doing so, you will help to
conserve natural resources and improve standards of environmental protection in treatment and
disposal of electrical waste (Waste Electrical and Electronic Equipment Directive).
Wifi & Bluetooth®
Hereby, STL Group, declares that this BT-125 is in compliance with the essential requirements
and other relevant provisions of Directive 1999/5/EC. The declaration of conformity may be
consulted at [email protected]
8
|