INSTALLATION AND OPERATION INSTRUCTIONS
DIRECT DRAW DISPENSER - SELF-CONTAINED MODELS
MODEL NOS.
DS Series
IMPORTANT INFORMATION
Table of Contents
Fill out the enclosed warranty card and mail to the
Perlick Corporation to register the warranty. If the
card is not returned, the warranty period will begin
from the date the equipment is shipped from the
factory.
PREPARING THE CABINET FOR USE
Specifications.........................................................2
List of Included Parts.............................................3
Tools Required.......................................................3
Plumbing................................................................3
Electrical ................................................................3
Installing Casters or Legs......................................3
Installing Faucet and Dispensing Head.................3
TAPPING
This manual has been prepared to assist you in the
installation of your Direct Draw Dispenser and to
acquaint you with its operation and maintenance.
Connecting the Keg Coupler .................................4
Tapping the Keg.....................................................4
Connecting the Regulator......................................5
Adjusting Gas Flow................................................5
CO2 Leak Test .......................................................5
Replacing a CO2 Gas Cylinder..............................5
Handling CO2 Gas.................................................5
TEMPERATURE
Beer Temperature..................................................6
Refrigeration and Temperature Control.................6
CLEANING
Cleaning the Beer Lines........................................7
Cleaning the Cabinet.............................................7
GENERAL INFORMATION
We dedicate considerable time to ensure that our
products provide the highest level of customer
satisfaction. If service is required, your dealer can
provide you with a list of qualified service agents. For
your own protection, never return merchandise for
credit without our approval.
We thank you for selecting a Perlick product and
assure you of our continuing interest in your
satisfaction.
WARNING: When lifting, the full weight of the
cabinet must be supported. Lift from the cabinet
base and not from the top. Improper lifting can
result in severe damage to the cabinet.
How to Pour a Perfect Glass of Beer....................8
Troubleshooting.....................................................9
Beer Facts .............................................................9
REPLACEMENT PARTS................................10-11
Wiring Diagram....................................................12
8300 West Good Hope Road • Milwaukee, WI 53223 • Phone 414-353-7060 • Fax 414-353-7069
Form No. Z2280
Preparing the Cabinet for Use – Direct Draw Dispensers Self-Contained
■
Apply RTV around the base of the dispensing
Parts List
head to seal it to the top. Align the dispensing
head over the holes on the cabinet top and use
screws provided to secure standard to cabinet
top. Wipe off excess RTV to complete the seal.
Attach faucet to standard using spanner
wrench to tighten coupling. Attach faucet
handle to faucet.
■
Faucet Standard.
■
Faucet Head Assembly.
Black Connector Hose 3⁄16” x 3’.
■
5⁄16” Air Hose.
■
■
■
Spanner Wrench.
Bag of Miscellaneous Parts.
■
■
Insert flexible plastic air hose six to seven
Suggested Tools Required
inches into bottom of faucet standard.
Secure hose with tie wrap (supplied).
■
#2 Phillips Screwdriver.
Spanner Wrench (included).
■
■
#10 Crescent Wrench.
Plumbing
9/16” Allen Wrench.
■
The floor drain in the right rear corner is equipped
with a 3/4” female pipe thread connection with side or
bottom access for beer drainer waste.
5/16” & 3/8” Nut driver.
Power driver.
■
■
■
Remove either side or bottom drain plug with an
Uncrating and Inspection
allen wrench and attach a 3/4” male pipe (provided
Remove all crating material before operating.
by plumber) to an external drain connection.
Carefully inspect cabinet for hidden damage. If
Evaporator condensate has been plumbed to a
damage is discovered, file your claim immediately
condensate pan located in the compressor housing.
with the transportation company. Perlick is
CAUTION: Do not overtighten drain fitting
not responsible for damage in transit.
as it may damage the threads.
Placing the Cabinet
NOTE: The end of the CO2 line extends through a
sleeve on the side of the cabinet in the
machinery compartment. Connect this
line to the pressure supply with a hose
and fitting.
Push the cabinet into place using rollers when
necessary. Important: Proper air flow around the
condensing unit is necessary for efficient operation.
Never obstruct the air flow in and out of the
condensing unit.
Electrical
Leveling the Cabinet
The cabinet must be connected to a separately
fused power source (see electrical specification
plate) and grounded in accordance with National
and Local Electrical Codes. Caution: Do not
attempt to operate the equipment on any other
power source than that listed on the Electrical
Specification plate.
When the cabinet is in place, check installation with
a carpenter’s level. A slight pitch to the drain side is
desired. Water may accumulate if the cabinet is
pitched to the opposite side.
Installing Casters or Legs (Optional)
Attach casters to the cabinet bottom in the holes
provided. Use supplied 1/4”- 20 x 3/4” hex head
self-tapping machine screws. Use power driver if
available.
WARNING!
To avoid compressor damage,after returning
cabinet to an upright position, let unit stand for
24 hours before plugging it in and running the unit.
Installing the Faucet and
Dispensing Head
Before you begin: Wash tapping devices and
faucet. Flush beer, tapping device and faucet lines
with fresh water.
Perlick is committed to continuous improvement. Therefore, we reserve the right to change specifications without prior notice.
Form No. Z2280
3
Installation and Tapping – Direct Draw Dispensers Self-Contained
Connecting the Keg Coupler
(when Supplied by Perlick)
Tapping a Single Valve Keg (Sankey):
■
Place one brown leather washer into black beer
line connector hose on hex nut side. Screw
connector to stainless steel beverage line on
faucet standard. Tighten with a wrench, but do
not over tighten.
Step 1
Single Valve Keg Coupler
■
Make sure lever handle on the keg coupler is in
the UP (untapped) position. Place one brown
leather washer into wing nut end of black beer
line connector hose and thread onto top of keg
coupler. Hand tighten.
Step 3
Step 2
■
Place clamp on one end of red air line. Push
end over air valve located inside cabinet.
Tighten clamp with screwdriver. Turn shut-off
valve to OFF (horizontal) position.
Place clamp on the other end of red air line and
push over tailpiece on coupler. Tighten clamp
with screwdriver.
■
■
Be sure beer faucet is in closed position.
Align keg lugs with lug openings on bottom
■
of coupler.
Turn clockwise 1⁄4 turn. Pull handle out and
■
CAUTION: Do not use keg coupler as a
handle to lift keg.
down. Keg is now tapped.
Open shut-off valve on air divider located inside
■
of the cabinet.
Important: Be sure to close this valve
when untapping keg.
Perlick is committed to continuous improvement. Therefore, we reserve the right to change specifications without prior notice.
Form No. Z2280
4
Installation and Tapping – Direct Draw Dispensers Self-Contained
Connecting the Regulator to the
CO2 Cylinder
Replacing CO2 Gas Cylinder
■
Turn CO2 hand valve clockwise until seated and
■
Remove blue plug from regulator fitting.
close shut-off valve on regulator.
Unscrew regulator from cylinder fitting.
■
(Note: Do not remove the carbonic washer).
Screw regulator onto gas cylinder valve. Tighten
■
■
Replace carbonic washer (Part No. 157F2P),
with wrench until vertically straight. Be sure that
shut-off valve (black lever) on regulator is in
the OFF (horizontal) position.
Place a screw clamp over end of red air line
and push onto regulator tailpiece. Tighten clamp
with a screwdriver.
if needed and reattach regulator to filled
cylinder.
Turn CO2 hand valve counterclockwise until
fully open. Turn regulator shut-off valve to
open position.
Adjust CO2 gas flow as required, turning
■
■
■
clockwise for higher pressure.
REGULATOR
FITTING
HAND
VALVE
CO2
Proper CO2 Handling
PRESSURE
GAUGE
30
20
40
PERLICK
ALWAYS...
50
60
10
PSI
0
■
Connect a regulator (reducing valve) to
CO2 cylinder.
Secure cylinder in upright position whether in
■
storage or in use.
Keep cylinder away from heat. Rupture disc
vents at 122° F. maximum.
Ventilate room after high pressure gas leakage.
CO2
GAS
DRUM
■
■
FITTING FOR
RED AIR HOSE
■
Check the last DOT test date on cylinder neck
before filling. If more than five years old, the
cylinder must be retested to DOT specifications.
Be sure CO2 cylinder outlet fitting is free of dust
or dirt before attaching regulator.
Store CO2 cylinder and regulator assembly
REGULATOR
ADJUSTING
SCREW
SHUT-OFF VALVE
(BLACK LEVER IN
CLOSED POSITION)
■
■
upright.
Adjusting the CO2 Gas Flow
■
Allow only properly trained and experienced
personnel to handle high pressure gas.
■
Turn regulator adjusting screw counterclockwise
until it turns freely.
NEVER...
■
■
■
Turn hand valve counterclockwise on CO2
cylinder to the fully open position.
Turn regulator adjusting screw clockwise until
desired pressure is reached (approximately
12-15 lbs.). Tighten stop nut on adjusting screw.
Open shut-off valve on bottom of regulator.
Connect cylinder directly to a keg without a
regulator (reducing valve).
Drop or throw regulator or CO2 cylinder.
Transport CO2 cylinder in a closed vehicle.
Apply oil to a regulator.
Shut off CO2 cylinder when not in use. You will
not save gas by doing so!
Allow untrained, inexperienced personnel to
handle high pressure gas.
■
■
■
■
■
CO2 Leak Test
■
Dilute a small amount of liquid dishwashing soap
and rub the soapy mixture around each connection.
If bubbles appear, tighten connection.
Failure to heed this warning could result in
personal injury or death.
Perlick is committed to continuous improvement. Therefore, we reserve the right to change specifications without prior notice.
Form No. Z2280
5
Draft Beer Information – Direct Draw Dispensers Self-Contained
Temperature
At temperatures lower than 30° F., beer will freeze.
When beer freezes, the alcohol in the beer may
separate and cause the beer to be cloudy with an
“off” taste.
One of the most common causes of dispensing
problems is improper temperature. Draft beer
should be stored at a temperature between 32° and
38°. At warmer temperatures, beer will foam.
Refrigeration and Temperature Control
Adjusting the temperature
The Direct Draw Dispenser is equipped with a
heavy-duty refrigeration system designed to
automatically maintain a storage temperature of
36-41 degrees F. The control is factory set at 38
degrees F.
The temperature control is inside the cabinet on
the right-hand side of the evaporator fan panel
assembly. You will need a screwdriver to turn the
adjusting screw. Make small adjustments until the
desired temperature is achieved.
■
Colder Temperatures:
Turn the adjusting screw clockwise (to the right).
Warmer Temperatures:
Turn the adjusting screw counterclockwise
(to the left).
4
■
5
3
The condenser fan motor turns off and on with the
condensing unit. The evaporator fan motor runs
continuously. The fan motors are lifetime lubricated
and will require no oiling.
2
6
1
NOTE:
COLD
OFF
Cabinet Temperatures lower than 34° will not allow
for proper defrosting of the evaporator coil. If
defrosting is necessary, turn the control knob to the
OFF position until coil is defrosted.
Perlick is committed to continuous improvement. Therefore, we reserve the right to change specifications without prior notice.
Form No. Z2280
6
Cleaning the Beer System – Direct Draw Dispensers Self-Contained
I
The entire beer system, to include the faucet, flexible
beer line and tapping devices must be cleaned at
regular intervals. We recommend flushing the entire
system with fresh water immediately after a keg has
been emptied. Once each month the system should
be cleaned chemically.
Beer Stone:
All beer contains calcium which is present from
the grains used in the brewing process. it is an
important natural material in draft systems in
that as it oxidizes it coats the internal parts of
the beer lines and equipment. This thin coat of
beer stone helps prevent the beer from picking
up strong metallic or plastic flavors as it flows
through the system. The beer stone will
continue to build if the system is not cleaned
properly or regularly and can cause drawing
problems if it begins to flake off. Beer stone is
present if one can see a brownish color on the
faucet or inner wall of the beer line, or tobacco-
like flakes in the beer.
It is recommended that you purchase Perlick’s
Pump Type Cleaning Kit. It is equipped with an
adapter that attaches directly to the faucet shank,
jar with pump, cleaning solution, faucet brush and
spanner wrench.
Cleaning the draft beer system will help to
eliminate the buildup of the following materials:
IIII Bacteria:
Beer is an excellent food for bacteria (none of
which is harmful). Proper conditions may begin
the growth of bacteria in draft beer and on the
beer faucet. By regular cleaning, we prevent
this bacterial buildup and maintain the quality
of the draft beer. Greenish or yellowish colored
material on the faucet may indicate bacterial
growth.
Cleaning the Cabinet
Use a mild detergent and water to clean the inside
and outside of the cabinet. Dry thoroughly. Never
use a scouring pad or abrasive cleanser.
NOTE: An industrial strength, commercial cleaner
can be used to clean the outside of painted
cabinets.
I
Yeast:
All domestic draft beers contain a small amount
of yeast which remains in the beer from the
fermentation process. When the temperature of
draft beer exceeds 50° a process of secondary
fermentation may take place. The beer faucet
may exhibit a white colored substance (yeast
build up) if not cleaned on a regular basis.
Cleaning the Condenser
Use a long handled, stiff brush to clean the dirt from
the front surface of the condenser. Keeping the
condenser free from dust and dirt will ensure effi-
cient operation.
CAUTION: Do not bend the fins while brushing the
front of the condenser.
Perlick is committed to continuous improvement. Therefore, we reserve the right to change specifications without prior notice.
Form No. Z2280
7
Pouring a Perfect Glass of Beer – Direct Draw Dispensers
➠
STEP 1
Start with a clean glass.
Place the glass at a
45° angle, one inch
below faucet. Do not
let the glass touch the
faucet. Open the faucet
all the way.
STEP 2
➠
After the glass has
reached half full,
gradually bring the
glass to the upright
position
➠
STEP 3
Let the remaining beer
run straight down the
middle of the glass.
This ensures proper
release of CO2 by
producing a 3⁄4” to 1”
foam head.
STEP 4
➠
Close the faucet quickly
and completely.
Perlick is committed to continuous improvement. Therefore, we reserve the right to change specifications without prior notice.
Form No. Z2280
8
Trouble Shooting – Direct Draw Dispensers Self-Contained
■
Beer Service Problems
Cloudy Beer:
Beer in glass appears hazy, not clear.
CAUSES:
■
Wild Beer:
Dispensed beer has either too much foam or
is all foam.
CAUSES:
■
Dirty glass.
■
Dirty faucet or beer line.
■
Frozen or nearly frozen beer.
■
Beer has been dispensed improperly.
■
Old beer.
Solution: See pouring instructions
■
Beer that has not been refrigerated for a
on page 8.
Regulator pressure is set too high.
long period of time.
■
■
Warm keg temperature.
Beer and CO2 Facts
Solution: Keg must be colder than
40°. Target temperature is between
36° and 38° F.
Cabinet door is opened and closed
frequently and temperature is warmer
than 38° F.
Keg
Size
No. of
Gallons
No. of
Oz.
No. of
Cases
No. of
12Oz.
Servings
Full Keg
Weight
■
Quarter
Half
73⁄4
151⁄2
992
1,984
3.445
6.889
105
210
87 lbs.
161 lbs.
Solution: Adjust temperature to between
36° and 38° F.
Kinks, dents or obstructions in the line.
Using oddly shaped glasses. Frosted,
waxed or styrofoam containers may
cause foaming.
Dispenser has been turned off for a
long period of time.
Faucet is bad, dirty or in a worn condition.
Regulator malfunction.
■
Beer foam is 25% liquid beer and 75% CO2
gas. Don’t waste it!
■
■
■
Most people prefer beer stored at 38° F.
Beer lines and faucets require regular cleaning
(see cleaning instructions on page 7).
A fully-charged 4.2 lb. CO2 cylinder will
dispense approximately 51⁄2 to 61⁄2 half barrels.
CO2 gas gives beer its sparkling effervescence.
It also gives beer its creamy head of foam.
■
■
■
■
■
■
■
Flat Beer:
Foamy head disappears quickly; beer lacks
brewery fresh flavor.
CAUSES:
■
Dirty glassware.
■
CO2 pressure is too low, due to leak or
pressure setting.
CO2 is turned off at night.
■
■
Cooler is too cold.
■
CO2 leak or defective (sticking)
check valve.
Sluggish CO2 regulator.
■
Perlick is committed to continuous improvement. Therefore, we reserve the right to change specifications without prior notice.
Form No. Z2280
9
Replacement Parts – Direct Draw Dispensers Self-Contained
MODEL NOS.
DS60B
DS60S
DS72B
DS72S
DS84B
DS84S
Condensing Units
Condensing unit 115 volt, 60 hz.
Condensing unit
Compressor
C22647
515301063
513200314
215315009
15352019
C22646
515301062
513200003
215315009
15352019
C22646
515301062
513200003
215315009
15352019
Fan motor assembly
Condenser coil
Terminal board
Overload protector
Relay
219101538
MRT20AGK5590
21351619
219101538
MRT22AGK5590
21351619
219101538
MRT22AGK5590
21351619
Capacitor
13556529
13556532
13556532
Evaproator Assembly
Self Contained complete
Evaporator coil
65555-1
C17511-1EP
65084
65555-2
C17511-2EP
65085
65555-2
C17511-2EP
65085
Liquid & Suction line
Fan blade
Fan motor
Evaporator fan guard
Temperature control
Bulb clamp
57699
C15239A
65557
61283
C6634
57699
C15239A
65557
61283
C6634
57699
C15239A
65557
61283
C6634
Wire harness, compressor bottom
Wire harness, evaporator
Lock
65560
65561
63762
65560
65561
63762
65560
65561
36762
Space, lock
63761-1
63761-1
63761-1
Lock rail
Grille rail
Condenser pan
Condenser end panel
Grille, black
65432-24SS
65432-12SS
65565-1
66215-1SS
66210-12
66210-12SS
65435-12SS
65576-1L
65526-1
65432-24SS
65432-12SS
65565-1
66215-1SS
66210-12
66210-12SS
65435-12SS
65576-4L
65526-2
65432-24SS
65432-12SS
65565-1
66215-1SS
66210-12
66210-12SS
65435-12SS
65576-2L
65526-2
Grille, SS
Condenser housing back
Evaporator, liquid & suction line cover
Evaporator pan
Door sill
65500-1
65500-1
65500-1
Door handle bracket
Door handle
Door gasket
65189-1
C31409-1
66237-4
65189-1
C31409-1
66237-4
65189-1
C31409-1
66237-4
Cabinet hinge
Cabinet hinge
Hinge pin
65436-LBRT
65436-LBRB
63679-1
65436-LBRT
65436-LBRB
63679-1
65436-LBRT
65436-LBRB
63679-1
Hinge assembly, cabinet left side
Hinge assembly, cabinet right side
65505L
65505R
65505L
65505R
65505L
65505R
Replacement door
*
RD-NL2
RD-NL2
RD-NL2
Perlick is committed to continuous improvement. Therefore, we reserve the right to change specifications without prior notice.
Form No. Z2280
10
Replacement Parts – Direct Draw Dispensers Self-Contained
For Single Valve Keg Coupler (Series D)
14
4
Item
No.
Part
No.
3
Description
1 .............32499................Probe assembly
2 ............F40184...............Probe body
3...........31080-2P.............Ball
1
2
4............43641-1..............Ball retainer
5...........31087-2P.............Probe washer
6 .............31089................“O” Ring - 3-per assembly
7 .............43061................Body
15
13
6
8...........23682-2P.............Check valve
9............157R2P ..............Washer
10............206B-1...............Tailpiece
8
9
10
11
11..............2026.................Coupling nut
12..........31088-2P.............Bottom seal washer
13...........31084-1..............Retaining screw
14 ...........43002A...............Yoke assembly w/lock
15 ...........43001A...............Yoke assembly standard
16...........32474-1..............Wrench
7
12
16
5
Miscellaneous
Part
No.
Description
157L2P................Beer line connector gasket
57F2P .................CO2 tank washer
1392R .................Red air hose
529 ......................Beer hose
2928D .................Twin gauge CO2 regulator
Perlick is committed to continuous improvement. Therefore, we reserve the right to change specifications without prior notice.
Form No. Z2280
11
Wiring Diagram – Direct Draw Dispensers Self-Contained
CAPPED
DS Series 2, 3 and 4 Keg Coolers
NOT USED
EVAPORATOR FAN
EVAPORATOR FAN
BLACK
WHITE
THERMOSTAT
BLACK
POWER CONNECTION
CONDENSING UNIT
BLACK
WHITE
GREEN
JUNCTION BOX
8300 West Good Hope Road • Milwaukee, WI 53223 • Phone 414-353-7060 • Fax 414-353-7069
Perlick is committed to continuous improvement. Therefore, we reserve the right to change specifications without prior notice.
Form No. Z2280
12
|