HTTP://WWW.PYLEAUDIO.COM
TV TUNER SYSTEM
PLTK120
,
OWNER S MANUAL
Selecting channels and adjusting the sound
Precautions
POWER
MUTE
Please read this manual completely and carefully before installing the equipment.
Use the CH+ and CH- buttons to select channels.
AVC
VOL-
AUTO
VOL+
CH+
Use the VOL+ and VOL- buttons to increase or decrease audio volume.
You will see a Volume Bar on screen indicating relative volume level.
To disable the audio output, press the MUTE button. To cancel the muting
function, press MUTE button again.
1. Do not operate this equipment while driving, safe driving should always be your highest priority.
2. Do not install these components in an area exposed to rain, moisture, direct sunlight, extreme
heat or cold, excessive dust, dirt or humidity.
MENU
CH-
TV TUNER
REMOTE
3. Immediately unplug the power cord and send the TV Tuner to your local dealer or service center as soon as
possible:
Please note: VOL+, VOL- and MUTE buttons are disabled in AV mode.
a) If there is smoke or any peculiar odor present during use.
b) If there is damage to any of the component casings.
Providing A/V audio to your car radio
If your radio has AUX line-level inputs, you can attach the A/V audio output
connectors to these inputs with RCA-RCA interconnect cables.
4. To avoid damage and risk of electronic shock, protect this equipment from getting humid or wet,
If this does occur, unplug the power cord immediately and send the unit to your local dealer
or service center as soon as possible.
5. Do not attempt to repair, open or disassemble any of the components. Dangerous high voltage is present
and may cause an electric shock.
6. Use only a power source with 12 Volts DC (negative ground).
7. Do not place objects on or suspend objects from the power cord, as this may damage the cord.
8. Do not twist or place the power cord near any source of heat in the vehicle.
9. Do not attempt to repair a damaged, broken or deffective power cord. Replace it with a new one immediately.
8
3
SYSTEM FEATURES AND CONTROLS
Remote function
POWER
MUTE
1. POWER: Power on/off
TUNER BOX
REMOTE CONTROL
AVC
VOL-
AUTO
VOL+
CH+
MENU
2. MENU: In AV mode push the MENU button to access on screen menu.
Use CH- or CH+ button to move on screen point to next or previous
command item. And use VOL+ or VOL- button to increase or decrease
current option value. In TV mode MENU is invalidated.
CH-
TV TUNER
REMOTE
MUTE
POWER
POWER KEY
AVC KEY
MUTE KEY
ANT IN
REMOTE
POWER
MUTE
AVC
VOL-
AUTO
VOL+
AUTO KEY
CH+ KEY
CH+
AVC
VOL-
AUTO
VOL+
Selecting the input mode
CH+
MENU
Tuner can switch between three different video sources using the
remote control. These modes are:
TV Mode: for receiving TV Channels.
AV1: external audio and video inputs for DVD, VCD or video game.
AV2: external audio and video inputs for DVD, VCD or video game.
MENU
VOL- KEY
CH- KEY
VOL+ KEY
MENU KEY
CH-
TV TUNER SYSTEM
TV TUNER
REMOTE
CH-
A/V OUTPUT
AUDIO VIDEO
POWER
MUTE
DC 12V
AUDIO
R
L
TV TUNER
REMOTE
Programming channels for TV
AVC
VOL-
AUTO
VOL+
CH+
The tuner system can memorize channels in both TV modes. Press the
AUTO button on the remote, the tuner will begin scanning all of the
available channels and put them into memory.
MENU
CH-
TV TUNER
REMOTE
7
4
Connection
Installation and Electrical Connections
1. Find a suitable location for the tuner unit and mount it securely
in place. Be sure to place it in an area away from moisture and
dirt, and where incoming cables will not be walked on or pulled
accidentally.
ANTENNA
INFRARED
REMOTE RECEIVER
REMOTE
ANT IN
2. Make all required audio, video and power connections to the
appropriate connectors on the tuner as indicated in the drawing
below to suit you system installation. Install the infrared remote
eye in a location you know will be available in line-of-sight with
the remote control use location.
TV TUNER SYSTEM
PLTK120
A/V OUTPUT
AUDIO
DC 12V
AUDIO
R
L
VIDEO
TO DC+12V
GROUND
Please note that the following drawing describes connections
for all system possibilities and your particular system may vary
from this.
POWER
AV
MENU
+
-
AV3
5
6
|