INSTALLATION INSTRUCTIONS FOR PART 99-9107B
APPLICATIONS
Audi A4 / S4
2002-2008
(With Symphony Radio)
99-9107B
KIT FEATURES
• DIN Head Unit Provision with Pocket
• ISO DIN Head Unit Provision with Pocket
• Double DIN Head Unit Provision
• Painted Matte Black to Match Factory
KIT COMPONENTS
• A) Radio Housing • B) Pocket • C) Trim Plate • D) ISO Brackets • E) Double DIN Trim Plate
• F) Double DIN Brackets
A
B
D
C
WIRING AND ANTENNA CONNECTIONS (Sold Separately)
Harness:
• 70-1787 - VW / Audi Harness 1993-up
Antenna Adapter:
• 40-VW10 - Euro Antenna Adapter 1986-up
F
E
TOOLS REQUIRED:
• (2) 86-9001 Head Unit Removal Tools • Small Flat Blade Screwdriver • Phillips Screwdriver
1-800-221-0932
© COPYRIGHT 2004-09 METRA ELECTRONICS CORPORATION
DASH DISASSEMBLY
99-9107B
AUDI A4 / S4 2002-2008 W/SYMPHONY RADIO
1
Disconnect the negative battery
terminal to prevent an accidental
short circuit.
A
2
3
Insert Metra’s 86-9001 into the
slots in the factory head unit and
pull the unit out.
(Figure A)
CD
AS
LOAD
FM
MENU
TONE
AM
Disconnect the wiring.
SAT
TAPE
RDS
SCAN
1
KIT ASSEMBLY
99-9107B
DIN HEAD UNIT PROVISION WITH POCKET
A
B
C
Snap the DIN cage into the Radio
Housing and secure by bending
the metal locking tabs down.
(Figure A)
1
2
Locate the factory wiring harness in
the dash. Metra recommends using
the proper mating adapter from
Metra or AXXESS. Re-connect the
negative battery terminal and test
the unit for proper operation.
Snap radio assembly into factory
radio opening.
3
4
5
Slide the aftermarket radio into the
cage and secure. (Figure B)
Snap the pocket into the Radio
Housing until secure. (Figure C)
NOTE: Once the dash kit is snapped
in, it cannot be removed without
dash panel removal
2
KIT ASSEMBLY
99-9107B
ISO DIN HEAD UNIT PROVISION
Mount the ISO Brackets to the
head unit with the screws sup-
plied with the unit. (Figure A)
1
2
A
Slide the head unit into the radio
opening until the slide clips
engage. (Figure B)
Snap the ISO Trim Plate into the
Radio Housing. (Figure B)
3
Snap the pocket into the Radio
Housing. (Figure C)
4
5
B
Locate the factory wiring harness
in the dash. Metra recommends
using the proper mating adapter
from Metra or AXXESS. Re-con-
nect the negative battery terminal
and test the unit for proper opera-
tion.
Snap the radio assembly into the
factory radio opening.
6
C
NOTE: Once the dash kit is snapped
in, it cannot be removed without
dash panel removal
3
KIT ASSEMBLY
99-9107B
DOUBLE DIN HEAD UNIT PROVISION
Cut and remove center divider
from radio housing. (Figure A)
1
2
A
Snap the DDIN brackets to the
inside edge of the radio housing.
(Figure B)
Slide the DDIN radio unit into the
DDIN bracket/radio housing
3
assembly and secure the unit to
the kit using the screws supplied
with the head unit. (Figure C)
Snap the DDIN trim-plate onto the
housing/radio assembly. (Figure C)
4
5
B
Locate the factory wiring harness
in the dash. Metra recommends
using the proper mating adapter
from Metra or AXXESS. Re-con-
nect the negative battery terminal
and test the unit for proper opera-
tion.
Snap radio assembly into factory
6
radio opening.
C
NOTE: Once the dash kit is snapped
in, it cannot be removed without
dash panel removal
4
99-9107B
NOTES
5
99-9107B INSTRUCTIONS
1-800-221-0932
REV. 10/26/09
© COPYRIGHT 2004-09 METRA ELECTRONICS CORPORA TION
INST99-9107B
|