STAINLESS STEEL BUILT-IN WINE/BEVERAGE COOLER
INSTRUCTION MANUAL
Model No.: MCWC50DSTF
MCBC58DSTF
To ensure proper use of this appliance and your safety, please read the
following instructions completely before operating this appliance.
NAMES OF THE PARTS
MODEL NO.: MCWC50DSTF
① Electronic thermostat
② Wine rack ③ Door gasket
④ Glass door ⑤ Cabinet
MODEL NO.: MCBC58DSTF
① Electronic thermostat
② Beverage shelf ③ Door gasket
④ Glass door ⑤ Cabinet
EN
2
SPECIFICATIONS – Model # MCWC50DSTF
Magic Chef 50 Bottle Stainless Steel
Product Description
Built-In Wine Cooler
Model No.
MCWC50DSTF
Height
Unit Dimensions
( inches )
Width
23.4”
Depth
24.4”
34.4”
Net Weight ( lbs)
99 lbs
SPECIFICATIONS – Model # MCBC58DSTF
Magic Chef 5.8 cu.ft. Stainless Steel
Product Description
Built-In Beverage Cooler
Model No.
MCBC58DSTF
Height
Unit Dimensions
( inches )
Width
23.4”
Depth
24.4”
34.4”
Net Weight ( lbs)
104 lbs
EN
3
IMPORTANT SAFETY INSTRUCTIONS
To reduce the risk of fire, electrical shock,
or injury when using your appliance, follow
these basic precautions:
WARNING
Read all instructions before using the wine or beverage cooler.
DANGER or WARNING: Risk of child entrapment.
To avoid the possibility of child entrapment, please take the following precautions
before throwing out the appliance.
-
Remove all doors from the unit.
-
Leave the shelves in place so that children may not easily climb inside.
Never allow children to operate, play with, or crawl inside the appliance.
Refrigerants: All refrigeration products contain refrigerants, which under the
guidelines of federal law must be removed before disposal of product. It is the
consumer’s responsibility to comply with federal and local regulations when
disposing of this product.
Never clean appliance parts with flammable fluids. The fumes can create a fire
hazard or explosion.
Do not store or use gasoline or any other flammable vapors and liquids in the vicinity
of this or any other appliance. The fumes can create a fire hazard or an explosion.
-Save these instructions-
INSTALLATION INSTRUCTIONS
Before Using Your Appliance
Remove the exterior and interior packing.
Before connecting the appliance to the power source, let it stand upright for approximately 4
hours. This will reduce the possibility of a malfunction in the cooling system from improper
handling during transportation.
Clean the interior surface with lukewarm water using a soft cloth. (Cleaning instruction on page 9)
Free-Standing Installation
This appliance is designed to be installed built-in or free standing.
Locate the appliance away from direct sunlight and sources of heat (stove, heater, radiator, etc.).
Direct sunlight may affect the acrylic coating and heat sources may increase electrical
consumption. Ambient temperature below 55°F (12.8°C) or above 77°F (25°C) will hinder the
performance of this appliance. This unit is not designed for use in a garage or any other
outside installation.
Avoid locating the appliance in moist areas.
Plug the appliance into dedicated, properly installed-grounded wall outlet. Do not under any
circumstances cut or remove the third (ground) prong from the power cord. Any questions
concerning power and/or grounding should be directed toward a certified electrician or an
authorized service center. This unit is not designed to be installed in an RV or used with an
inverter.
After plugging the appliance into a wall outlet, turn the unit on and allow the unit to cool down for 3
~ 4 hours under before placing wine bottles or beverages in the appliance.
EN
4
Built-In Installation
The cutout dimension illustrated in figure (A) allows for door
swing and access to the pull-out shelves when installed as
a built-in appliance. If installing between frameless cabinets,
a ½” wide filler strip or side panel may be needed on hinge
side. The filler strip will act as a spacer between the
appliance case and adjacent cabinet door swing.
The width of the opening must include the filter panels.
Note:
The door should protrude at least 1” beyond the
surrounding cabinets.
If door reversal is desired, please follow Reversible door
instructions on page 8 of this manual prior to installation.
Figure A
The cutout depth must be 24”.
Electrical Connection
WARNING
Improper use of the grounded plug can result in the risk of electrical shock. If the power cord is
damaged, have it replaced by an authorized service center.
This appliance should be properly grounded for your safety. The power cord of this appliance is
equipped with a three-prong plug which mates with standard three prong wall outlets to minimize the
possibility of electrical shock.
Do not, under any circumstances, cut or remove the third ground prong from the power cord supplied.
This appliance requires a standard 115 Volt A.C. /60Hz electrical outlet with three-prong ground.
This appliance is not designed to be used with an inverter.
The cord should be secured behind the appliance and not left exposed or dangling to prevent
accidental injury.
Never unplug the appliance by pulling the power cord. Always grip the plug firmly and pull straight out
from the receptacle.
Do not use an extension cord with this appliance. If the power cord is too short, have a qualified
electrician or service technician install an outlet near the appliance. Use of an extension cord can
negatively affect the performance of the unit.
If any problems with the appliance persist, please contact our Customer Service Dept. to consult with
a representative at 888 775-0202 or visit our website to request warranty service at
EN
5
APPLIANCE FEATURE
MCWC50DSTF: Wine Cooler
Engaged Wine Shelves
There are five wine shelves of full depth in upper part of
cabinet to store wine bottles.
The second supporting guide (Counted from top, see
illustration “A”) is not designed for wine shelves. It is only
for beverage shelf.
All the top five wine shelve have tabs to engage the
cabinet on both sides.
Any of the wine shelve can be removed to accommodate
larger bottles.
To Remove a Shelf:
Remove all bottles from the shelves.
Lift the shelve upwards and then gently pull out the shelves.
To Replace a Shelf:
Place the sides of the shelves back onto the supporting guides of the cabinet and push back until
the shelf tabs slide into place.
NOTE: Ensure that the tabs are firmly engaged in place before storing any bottles.
Bottle Arrangement
The top five shelves each hold 8 bottles with the bottle necks
alternating front to back.
The bottom rack, which consist of two stories, each holds 6
bottles with bottle necks facing the front.
MCBC58DSTF: Beverage Cooler
Engaged Beverage Shelves
There are three glass shelves to store beverage cans or
bottles.
All three glass shelves have tabs to engage the cabinet
on both sides.
The shelves may be arranged on any supporting guide as
preferred.
Any of the glass shelves can be removed to
accommodate larger cans or bottles.
To Remove a Shelf:
Remove all cans or bottles from the shelves.
Lift the shelve upwards and then gently pull out the
shelves.
To Replace a Shelf:
Place the sides of the shelves back onto the supporting guides of the cabinet and push back until
the shelf tabs slide into place.
NOTE: Ensure that the tabs are firmly engaged in place before storing any beverages.
Warning:
Do not press/jostle the circulation fan in the cabinet when you place in or remove the beverage
cans or bottles.
Properly store your beverages so that the cans or bottles do not hinder air circulation inside the
cabinet.
EN
6
OPERATING YOUR APPLIANCE
MCWC50DSTF: Wine Cooler
The temperature range of the wine cooler is for 39°F ~
64°F (4°C ~ 18°C) +/- 5°F.
Temperature Recommendations:
Red Wine:
White Wine:
54°F ~ 61°F (12°C ~ 16°C)
43°F ~ 50°F (6°C ~ 10°C)
The display indicates the average temperature of the appliance at the moment.
Pre-Set Wine Zones
Press the “RED” or “WHITE” pads to choose preset storage conditions for either red or white
wine. (The indicator light “RED” or “WHITE” will illuminate accordingly.)
The programmed temperature for red or white wine will be displayed for a few seconds.
Manual Temperature Setting
The temperature of the wine cooler can be set anywhere between 39°F ~ 64°F (4°C ~ 18°C) by
pressing temperature up ▲ and temperature down ▼pads as follows:
1) Press the [SET] pad until you hear a “Beep” sound (approximately 2 seconds).
2) Press the ▲▼ pads to increase or decrease the desired temperature in increments of
one degree.
3) Press the [SET] pad to confirm your desired temperature setting. If no pad is pressed
within 10 seconds, your select temperature setting will be automatically confirmed.
NOTE:
To select temperature display between Celsius (°C) or Fahrenheit (°F), press the “▲” pad for
approximately 2 seconds.
MCBC58DSTF: Beverage Cooler
The temperature range of the beverage cooler is for 39°F ~
54°F (4°C ~ 12°C). +/- 5°F.
The display indicates the average temperature of the
appliance at the moment.
NORMAL Temperature Setting
When the appliance is switched on, or the “NORMAL” pad is pressed, the appliance runs on the
temperature setting of 45°F (7°C) and the “NORMAL” indicator light will be illuminated.
Manual Temperature Setting
The temperature of the beverage cooler can be set anywhere between 39°F ~ 54°F (4°C ~ 12°C)
by pressing temperature up ▲ and temperature down ▼pads as follows:
1) Press the [SET] pad until you hear a “Beep” sound (approximately 2 seconds).
2) Press the ▲▼ pads to increase or decrease the desired temperature in increments of
one degree.
3) Press the [SET] pad to confirm your desired temperature setting. If no pad is pressed
within 10 seconds, your select temperature setting will be automatically confirmed.
NOTE:
The “MANUAL” indicator light will be illuminated while you are manually setting the temperature
on the beverage cooler.
To select temperature display between Celsius (°C) or Fahrenheit (°F), press the “▲” pad for
approximately 2 seconds.
The following is applicable to both MCWC50DSTF and MCBC58DSTF:
The
idle cycle.
indicator will remain ON during refrigeration cycle and will be OFF during
To switch the Interior light ON/OFF, press the
pad.
EN
7
Changing The Inner Light
Before removing the inner light, turn off the appliance first and then unplug the unit from the wall
outlet. Failure to do so could result in electrical shock or personal injury.
Use Phillips screwdriver to take out the screw.
Remove the transparent light cover gently.
Pull out the existing light bulb by unscrewing it counter-clockwise.
Insert new light bulb (E12, max. 15W) by screwing it in clockwise.
Replace the transparent light cover and tighten screw.
Automatic Defrost
There is no need for manual defrosting of this appliance due to automatic defrosting function.
The ice build-up on the inner back wall during compressor operation will be automatically
defrosted once the compressor cycle is off.
Defrost water will drain out passing through the drain outlet in the inner back wall into a drain pan
located above the compressor, from where it evaporates.
CHANGING THE REVERSIBLE DOOR
This appliance is built with a reversible door. You have the choice of either opening it from the left or
the right side. In order to reverse the opening direction of your door, please follow these simple
instructions. NOTE: If desired, please change the door swing prior to appliance installation.
Caution: To avoid personal injury to yourself and/or property, we highly recommend that
someone assist you during the door reversal process.
1) Remove the top hinge assembly and keep
them for later use.
2) Remove the bottom hinge assembly and
keep them for later use.
3) Remove the plug buttons from the upper left
holes and transfer them to the uncovered
holes on the right side. Be sure to press the
plug buttons firmly into the hole.
4) Re-install the top hinge assembly previously
removed in step 1 on the opposite side.
5) Re-install the bottom hinge assembly
previously removed in step 2 on the
opposite side.
6) Re-install the door assembly with the door
handle on the opposite side. (Rotating the
door assembly 180°).
7) Ensure that the door assembly is properly
aligned with cabinet before tightening the
screws.
EN
8
CARE AND MAINTENANCE
Cleaning Your Appliance
Upon installation of your new appliance, it is recommended that it be cleaned thoroughly.
Turn off the appliance first and then unplug the unit from the wall outlet.
Remove all contents.
Wash the inside with a damp warm cloth soaked in lukewarm water and baking soda solution.
The solution should be about 2 tablespoons of baking soda to a quart of water.
Be sure to keep the door gasket (seal) clean to keep the unit running efficiently.
The outside of the appliance should be cleaned with mild detergent and warm water.
Dry the interior and exterior with a soft cloth.
Dust or anything else blocking the vent may hinder the cooling efficiency of the appliance.
Vacuum the vent if necessary.
Vacation Time
Turn off the appliance first and then unplug the unit from the wall outlet.
Remove all the contents.
Clean the appliance.
Leave the lid open slightly to avoid possible formation of condensation, mold, or odors.
Short vacations: Leave the appliance operating during vacations of less than three weeks.
Long vacations: If the appliance will not be used for several months, remove all content and
unplug the power cord. Clean and dry the interior thoroughly. To prevent odor and mold growth,
leave the door open slightly: blocking it open if necessary.
Moving Your Appliance
Turn off the appliance first and then unplug the unit from the wall outlet.
Remove all the contents.
Securely tape down all loose items inside your appliance.
Tape the doors shut.
Energy Saving Tips
The appliance should be located in the coolest area of the room, away from heat producing
appliances or heating ducts, and out of the direct sunlight.
Ensure that door is closed when the appliance is turned on.
EN
9
TROUBLESHOOTING GUIDE
You can solve many common appliance problems easily, saving you the cost of a possible
service call. Try the suggestions below to see if you can solve the problem before calling for
service.
PROBLEM
Appliance does not operate.
POSSIBLE CAUSE
Not plugged in.
The circuit breaker tripped or a blown fuse.
Temperature control is set too warm. Turn the
control to a cooler setting and allow several hours
for the temperature to stabilize.
Temperature inside the appliance is too warm.
Door is kept open too long or is opened too
frequently. Warm air enters the appliance every
time the door is opened. Open the door less
often.
The door is not closed completely.
The door gasket does not seal properly.
The appliance has recently been disconnected
for a period of time. 4 hours are required for the
appliance to cool down completely.
Temperature inside the appliance is too cold.
Vibrations.
Temperature control is set too cold. Turn the
control to a warmer setting and allow several
hours for the temperature to stabilize.
Check to assure that the appliance is on a level
surface.
The appliance is touching the wall. Re-level the
appliance and move it from the wall.
If continued vibration occurs, turn off the
appliance and unplug the power plug. Contact
Customer Service Dept. for further assistance.
Door is slightly open.
Moisture forms on inside appliance walls.
Door is kept open too long, or is opened too
frequently. Open the door less often.
The door is not sealed properly.
Moisture forms on outside of appliance.
The door will not close properly.
Door is slightly open, causing cold air from inside
the appliance to meet warm moist air from
outside.
The appliance is not on a level surface.
The gasket is dirty.
EN
10
Appliance Warranty
MC Appliance Corporation warrants each new appliance to be free from defects in material
and workmanship and agrees to remedy any such defect or to furnish a new part(s) (at the
company’s option) for any part(s) of the unit that has failed during the warranty period. Parts
and labor expenses are covered on this unit for a period of one year after the date of
purchase. In addition, MC Appliance Corp. warrants the compressor (parts only) to be free
from defects in material and workmanship for a period of 5 years. The consumer is
responsible for all labor and transportation expenses related to the diagnosis and
replacement of the compressor after the initial one-year warranty expires. If in the event that
the unit is determined to be non-repairable under the terms of this warranty, the consumer is
responsible for all transportation expenses to return the unit to our factory prior to receiving a
refund. A copy of the dated sales receipt / invoice is required to receive warranty
service or a refund.
This warranty covers appliances in use within the continental United States, Puerto
Rico and Hawaii. The warranty does not cover the following:
.
.
.
.
.
.
.
Damages due to shipping damage or improper installation.
Damages due to misuse or abuse.
Content losses due to failure of the unit.
Inside components such as door panels, door shelves, racks, light bulbs, etc.
Punctures to the evaporator system due to improper defrosting of the unit.
Repairs performed by unauthorized service agents.
Service calls that do not involve defects in material and workmanship such as
instruction on proper use of the product, door reversal or improper installation.
Replacement or resetting of house fuses or circuit breakers.
Failure of this product if used for other than for its intended purpose.
Disposal costs for any failed unit not returned to our factory.
Any delivery costs incurred as the result of a unit that fails to perform as specified.
.
.
.
.
This warranty is in lieu of all warranties expressed or implied and no representative or
person is authorized to assume for us any other liability in connection with the sale of
this product. Under no circumstances is the consumer permitted to return this unit to
the factory without prior written consent from MC Appliance Corporation.
Model
Parts
Labor
Compressor Type of Service
(part only)
MCWC50DSTF
MCBC58DSTF
One-Year
One-Year
One-Year
One-Year
Five-Year
Five-Year
In-Home
In-Home
For Service or Assistance please call 888 775- 0202. Or visit us on the web at
www.mcappliance.com to request warranty service.
EN
11
|