Lucent Technologies Cordless Telephone MDW 9030P User Manual

MDW 9030P Wireless

Pocketphone Quick Reference

503-801-161

Comcode 107993149

Issue 2

March 1997

MDW 9030P Wireless

Pocketphone Quick Reference

Handset Controls

Receiver

Headset On/Off

Receives the sound

of your caller's voice,

unless a headset is

connected.

Press to turn the headset on

if the headset is plugged in.

ON appears in handset

display. To turn off, press

again. Turn on to make or

answer a call, and turn off to

“hang up.”

Antenna

Extend fully to

maximize the handset

range and voice

quality.

Lanyard Loop

Attach lanyard for

carrying handset.

Handset Display

Displays status of

lines and range. Also

see “Handset

Display” on next

page.

Volume Control

Press "+" to increase

or "-" to decrease

volume of receiver or

alerter.

212 555 1212

MSG ON

Column

On/Off

Use, with Select

Press to turn the

handset on. ON

button, to choose a

line or programmable/

intercom/drop button.

appears in handset

display. To turn off,

press again. Turn on to

make or answer a call,

and turn off to “hang

up.”

Redial

Press to dial again

the last number

manually dialed from

the handset.

Redial

Mute

On/Off

Feat/P

Conf

ABC

DEF

Feat/P

(Feature/Program)

GHI

JKL

MNO

Select

WXYZ

PQRS

TUV

Press to use dial-code

features (PARTNER^®

systems only) or to

enter programming

mode.

Trans

Hold

Use to move the

Selection rectangle,

and, with Column

buttons, to choose a

line or programmable/

intercom/drop button.

Also use to wake-up

the phone.

OPER

TransTalk

Conf (Conference)

Press to conference

in (add) another

party to your call.

Mute

Press to turn the micro-

phone off for privacy .

Headset Connector

(Transfer)

Trans

Press to transfer

a call to another

extension.

Hold

Press to put a call on

hold.

Plug in the headset cord

to use the headset.

- 1 -

Handset Display

RANGE

MUTE

MSG

Information you would see on a wired system phone's display,

(except time), based on your communications system:

LCL:P, D, M1, or M2= Local Mode:communications system

WIRELESS TEST=Handset in Wireless Test Mode

VIBR=Vibrator enabled

PSEL=Line Preselection enabled

PRESELECTION:ON / OFF=Line Preselection Mode:status

CHANGE BUTTN MAP=Communications system setting is wrong

MAP:P, D, M1, M2=Button Mapping Mode: setting

NO LINK=Handset is not communicating with radio module

MSG indicates that you have a message.

RANGE indicates that the handset is out of range or almost out of

range. Handset also beeps.

ON indicates that handset was turned on by pressing O.

Battery icon flashes to indicate a low battery condition. Handset

also emits 2 beeps.

No Ring icon indicates that the alerter is disabled.

MUTE indicates that handset microphone was turned off by

pressing M.

Line Status Indicators show the status of line or programmable/

intercom/drop buttons. See "Line Status Indicators" below.

Selection rectangle indicates the active row for line or program-

mable/intercom/drop button selection.

When the display is blank, the handset is either turned off or in "sleep"

mode. Activate the display by pressing O or ".

Line Status Indicators

Each line status indicator corresponds to a specific outside line or

programmable/intercom/drop button:

PARTNER Systems

A triangle (

A rectangle (

) is the equivalent of a green LED on a wired phone.

) is the equivalent of a red LED on a wired phone.

All Other Systems

A triangle (

A rectangle (

) is the equivalent of a red LED on a wired phone.

) is the equivalent of a green LED on a wired phone.

- 2 -

Volume Adjustment

To increase or decrease the volume of the handset alerter or the

receiver (earpiece):

■

Alerter: Press the "+" or the "–" button while the MDW 9030P

is awake but turned off. If the display is dark (the phone is in

"sleep" mode), press " to wake it up, then press the "+" or

the "–" button.

■

Receiver: Press the "+" or the "–" button while the MDW

9030P is turned on.

Battery Charger LEDs

The color of the battery charger's LEDs indicates the state of the

corresponding battery pack, as shown in the following table:

If it is the

If it is the SPARE

LED, the battery

pack in the Spare HANDSET LED,

battery

REFRESH LED,

the Refresh button

was pressed, and

If it is the

Battery

charger

the battery pack in the Handset

LED shows... compartment...

the Handset...

battery pack...

Steady

orange

Is charging

N/A

Steady green Is fully charged

Is fully charged

Has one of the

N/A

Flashing red

Has one of the

following problems: following problems:

* See note.

•

Is not seated

properly in the

charger

•

Is not seated

properly in the

charger

•

Has dirty

contacts

•

Has dirty

contacts

Is defective

Steady red

Is in the Discharge Is in the Discharge Is in the Discharge

portion of the

Refresh cycle.

portion of the

Refresh cycle.

portion of the

Refresh cycle.

*Note: If either the SPARE LED or the HANDSET LED is flashing red, both

battery packs must be removed from the charger to clear the flashing-red

condition. Address the possible problems for one battery pack at a time to

determine whether one is bad.

Help!

If you need help when using your MDW 9030P with a PARTNER,

MERLIN^®, or MERLIN LEGEND^®system in the continental U.S.,

call 1 800 628-2888. For all other systems, follow the procedure

you normally use to get support for your communications

system. Outside the continental U.S., contact your Lucent

Technologies Representative or local Authorized Dealer.

- 3 -

Making a Call

1. Press O.

2. If desired, press " to move the Selection rectangle; then press '

corresponding to the line you want.

3. Dial the call.

4. To end the call, press O.

Answering a Call

1. Press O.

2. Speak into the handset.

3. To end the call, press O.

Preselecting a Line or Button

Once Line Preselection is enabled, proceed as follows:

1. If the display is blank, press ".

2. If necessary, press " to move the Selection rectangle.

3. Press ' corresponding to the line or button you want.

4. Press O to access the line or button.

Changing Settings or Performing Tests

in Local Mode

1. Make sure the handset is turned off.

2. Press and hold " for 3 seconds.

3. While still holding ", press O.

4. Press one of the following:

A (2) to enable or disable the alerter.

P (7) for 3 seconds, then " to enable or disable Line Preselection.

V (8) to enable or disable the vibrator.

W (9) to enter Wireless Test Mode, then

1 for signal strength

2 for voice quality

3 for matching radio module and slot number

# to enter Local Test Mode.

5. Press O to exit.

CAUTION:

The MDW 9030P handset is a radio device and, like all radio

devices, should not be placed next to a pacemaker. See

"Guidelines for Safe and Efficient Operation" in MDW 9030P

Wireless Pocketphone Installation and Use for more information.

PARTNER, MERLIN, and MERLIN LEGEND are registered trademarks of

Lucent Technologies.

Lucent Technologies 503-801-161

Comcode 107993149

Issue 2, March 1997

- 4 -

Krown Manufacturing Universal Remote KA1000RR User Manual
LG Electronics Log Splitter LSVFSD LP User Manual
Life Fitness Elliptical Trainer 9100R User Manual
Loewe Flat Panel Television L 26 DVB T C CI User Manual
Makita Brush Cutter RBC220 User Manual
Makita Cordless Drill BHR241 User Manual
Makita Drill BDF452 User Manual
Makita Sander BO370 User Manual
Marshall electronic Microphone CE90V User Manual
Memorex TV DVD Combo MVD2009CB User Manual