BC-9009U BATTERY CHARGER - TABLE OF CONTENTS
Topic
BC-9009 Battery Charger Instruction Manual Contents
Page
Features
Inventory Of Contents
Function Keys
3
4
5
Language
Page
1
Operating Modes
Charge Mode
8
English
Discharge Mode
Refresh Mode
Test Mode
16
18
19
22
22
29
30
31
32
36
Trickle Charge
Display Mode Information
The Size C and D Battery Adapter
Care and Maintenance
Specification
Warranty Information
Troubleshooting
1
CAUTIONS:
BATTERY CHARGER BC-9009U
Instruction Manual
1.
The charger is restricted to charging NiCd and NiMH rechargeable batteries only.
Never use this charger for other types of batteries such as alkaline, lithium, carbon zinc
or other types that are not specified.
INTRODUCTION:
Congratulations on purchasing this intelligent charging unit which enables quick and optimum
charging to “AA” and “AAA” rechargeable batteries. With charging, discharging, refreshing and
capacity test functions as well as individual LCD displays for charging compartments; this
charging unit is reliable, user-friendly and ideal for use in the home, office or on a journey.
2.
3.
The charging unit should only be used at normal indoor room conditions.
Always follow the charging instructions for the rechargeable battery. Observe the
recommended charging current of the rechargeable batteries. Never use a charging
current higher than recommended in the charging process.
Never use any power cable and transformer other than those originally supplied with
the charging unit.
The rechargeable batteries may become hot during charging (especially when a high
charging current is chosen). User should take extra care when taking out the batteries
after charging.
4.
5.
The Charging unit
6.
Unplug the charging unit from the power source when not in use.
FEATURES:
The Charging unit
Charging rechargeable batteries in various currents (200, 500, 700 or 1000 mA). The
2
3
CHARGE MODE
Charging at 200 mA is the default-operating mode of the charging unit.
When only one or two rechargeable batteries are charged, provided that only compartment 1
and compartment 4 are used, a charging current up to 1500 or 1800 mA may be set by the
pressing the CURRENT key.
On the other hand, when charging three or four rechargeable batteries at the same time, user
may select a charging current of 200, 500, 700 or 1000 mA.
When charging two batteries at
compartment 2 & 3 – max.
charging current: 1000 mA
When charging four batteries –
max. charging current: 1000 mA
The estimated time of charging by various charging current is tabulated in Table 1.
When charging two batteries at
compartment 1 & 4 – max.
charging current: 1800 mA
When charging two batteries at
compartment 1 & 2 – max.
charging current: 1000 mA
8
9
Table 1. Charging Time with various charging current
200
~4 hr
Size of battery
Battery Capacity Charging current selected Estimated charging time
(mA)
Note:
User shall always observe the recommended maximum charging current of the
rechargeable batteries. In general, 200 mA is a recommended charging current if rapid
charging is not necessary. It is definitely safe and optimum to the rechargeable
batteries.
It may be necessary to charge and discharge the new rechargeable batteries several
times in the beginning before the optimum capacity of the rechargeable batteries can
be obtained. It is recommended to use the "Refresh" mode for new rechargeable
batteries in order to achieve the optimum battery capacity.
When the transformer has been plugged into the power source, the version number of
the charger (for example “33” ) will be displayed first. Then all the segments will light up
momentarily and the “null” sign will be shown before batteries are placed. If damaged
batteries are placed into the charging unit, the charger will also show “null” on LCD.
1800
1500
1000
700
500
200
1800
1500
1000
700
500
200
~80 min
~100 min
~2 hr 30 min
~3 hr 30 min
~5 hr
AA
2600 mAh
~12 hr
~70 min
~80 min
~2 hr
~3 hr
~4 hr
~10 hr
~70 min
~1 hr 40 min
AA
2000 mAh
1000 mAh
700
500
AAA
“null” displayed - No battery or damaged battery is
placed to the charging unit
10
11
setting. Afterward, the current can no longer be changed during the process and the
selected mode will begin.
START CHARGING THE RECHARGEABLE BATTERIES
Once a rechargeable battery is inserted after the transformer has been plugged into the
power source, the battery voltage (for example, “1.39V”) will be displayed for 4 seconds. Then
“200 mA Charge” (default mode) will be shown on LCD for another 4 seconds, indicating that
charging with 200 mA is to be started if no alteration in setting is made.
Within this 8-second time from inserting the batteries the user may first select the
operating mode by the MODE key. “Charge”, “Discharge”, “Refresh” and “Test” mode
may be chosen.
Charging current: 200 mA
After 8 seconds from the last key
press, the LCD will blink once to
indicate the setting is confirmed and
the selected mode is activated
Charge Mode
Then within 8 seconds from the last key pressing, user may select the charging/
discharging current by pressing the CURRENT key.
Note:
The mode key shall first be pressed and held for about 1 second to activate the mode
change. The subsequent pressing of the mode key will toggle between the “Charge”,
“Discharge”, “Test” and “Refresh” mode.
There is an 8-second time allowed for choosing further functions after each key
pressing. If no more keys are pressed, the LCD will blink one time to indicate the end of
12
13
“Full” sign is shown -The battery
is fully charged
Note :
The current cannot be altered once the setting has been confirmed in the initial stage.
This prevents the user from changing the current setting accidentally while setting other
rechargeable batteries. If one wants to change the applied current afterward, the
rechargeable batteries must be taken out and inserted again.
The maximum charging current of the other rechargeable batteries is restricted by the
current setting of the first inserted rechargeable battery. For instance, if the first
inserted rechargeable battery is set to charge at 700 mA, then the second, third and
During charging, the different displays- Charging current (in mA), Time elapsed (in hh:mm),
Terminal voltage (in V) and Accumulated capacities (in mAh or Ah) may be toggled and
selected by pressing the DISPLAY key (refer Table 4).
After the rechargeable battery is fully charged, “Full” will be shown on the display and the user
may take out them at this time. If the rechargeable batteries are left in place in the
compartments, trickle charging will start. The trickle charging current is around 5% of the
selected charging current to keep the rechargeable batteries full.
14
15
fourth rechargeable batteries can be only set to charging at a maximum current of 700
mA.
Therefore, the user is advised to place the battery with the highest expected charging
current in Compartment 1 first. To release the restriction of setting charging current,
user must take out all four rechargeable batteries from the charging unit.
To change the operating mode during charging, one can press the MODE key (for
selecting all rechargeable batteries) or NUMBER key then MODE key (for selecting
individual rechargeable battery). 8 seconds after the last key press the LCD will blink
one time to indicate the end of changing.
When overheating conditions occur (over about 127°F (53°C)), usually due to too high
a charging current selected), the charging will be stopped immediately and the display
will read “000 mA”, the charging process will only resume once the temperature of the
rechargeable batteries drops to a safe level. If overheating conditions continue to
occur, the rechargeable batteries must be taken out to cool down and then charged at
a lower current.
For a new rechargeable battery it is recommended to charge it with 200 mA current to
re-condition it from the long storage status.
DISCHARGE MODE
Discharge mode will first discharge the rechargeable battery then charge it. It is for removing
the memory effects of rechargeable batteries.
By pressing the MODE key within 8 seconds after inserting the rechargeable batteries, the
Discharge mode can be selected. Then the user may also select different discharging current
(see Table 2) by pressing the CURRENT key, within 8 seconds after inserting the batteries.
(The display will blink once to indicate the setting has been confirmed and the current cannot
be changed afterward.)
Discharging current: 250 mA
Discharge Mode
17
When the battery is overheated the
charging will cease automatically. “000
mA” will be displayed.
16
displayed.
Note:
The discharging current is always set to be half of the coming charging current whose
upper limit is 1000 mA (see Table 2). Therefore the user is recommended to carefully
select the discharging current so that the charging current afterward will not be too
high.
The mode key shall first be pressed and held for about 1 second to activate the mode
change. The subsequent pressing of the mode key will toggle between the “Charge”,
“Discharge”, “Test” and “Refresh” mode.
REFRESH MODE
Old rechargeable batteries and those that have not been used for a long time require
refreshing. This process will recover the optimum capacity of the rechargeable batteries. By
pressing the MODE key within 8 seconds after inserting the rechargeable batteries, the
Refresh mode can be selected.
Refresh mode will start with discharging the rechargeable battery, then charging it. The
repeated discharging and charging cycles will be launched until no further increase in the
measured capacities is estimated.
Table 2. DISCHARGE MODE Current
User-selected Discharging
100 mA
200 mA
250 mA
500 mA
350 mA
700 mA
500 mA
current
Thereafter Charging
current
Discharging current: 250 mA
1000 mA
Finally, batteries will be fully charged in discharge mode and “Full” will be displayed. If the
user presses the DISPLAY key at this time, "charge" icon instead of "discharge" icon will be
Refresh mode (the battery is
being discharged)
18
19
In the Test mode the rechargeable batteries will first be fully charged and then discharged to
determine the capacities. Finally, the rechargeable batteries are charged up again and the
capacity in (mAh) of (Ah) will be estimated and shown after the discharging ends.
By pressing the MODE key within 8 seconds after inserting the rechargeable batteries, the
Test mode can be selected. (The mode key shall first be pressed and held for about 1 second
to activate the mode change. The subsequent pressing of the mode key will toggle between
the “Charge”, “Discharge”, “Test” and “Refresh” mode.)
Note:
By pressing the MODE key within 8 seconds after inserting the rechargeable batteries,
the Refresh mode can be selected. (The mode key shall first be pressed and held for
about 1 second to activate the mode change. The subsequent pressing of the mode
key will toggle between the “Charge”, “Discharge”, “Test” and “Refresh” mode.)
Then the user may also select different discharging current by pressing the CURRENT
key (see “Note” in Discharge mode and Table 2), within 8 seconds after inserting the
batteries. (Or the display will blink once to indicate the end of setting and the current
cannot be changed afterward.).
The Charging
current in (mA)
It may take up to several days to finish the refreshing process, depending on the
selected discharging current.
The maximum refresh current is 1000 mA and is not affected by the number of
rechargeable batteries inserted.
Test mode
Note:
After selecting the Test mode the user may select different charging currents in the
Test mode by pressing the CURRENT key, within 8 seconds after the batteries are
TEST MODE
20
21
inserted. The afterward-discharging current will be half of the selected charging current
(see Table 3).
Table 3. TEST MODE Current
User-selected Charging
current
Thereafter Discharging
current
TRICKLE CHARGING
After the rechargeable battery is fully charged in any of the operating modes, the charger will
give a small amount of current to the rechargeable batteries to maintain the fully charged
level. This mode is automatically launched after rechargeable batteries are fully charged and
kept in the charging unit. The signal “Full” will be displayed on the LCD.
200 mA
100 mA
500 mA
250 mA
700 mA
350 mA
1000 mA
500 mA
The maximum charging current is 1000 mA and is not affected by the number of
rechargeable batteries inserted.
After the test mode is finished, the display will shift between the “Full” sign and the
battery capacity (in mAh or Ah) automatically in 3-second intervals until the
rechargeable batteries are removed. The user can switch to other displays by pressing
the DISPLAY key.
DISPLAY MODE INFORMATION
The user can use different display modes to monitor the rechargeable battery condition during
the different operations (see below figure and Table 4 to 7).
Battery capacity displayed in
(mAh) as the checking is
finished in Test mode.
22
23
Table 4. Various displays in Charge Mode
Different display modes are
exhibited: Charging current, Time,
Voltage and Capacity
Various displays (toggled by pressing DISPLAY key)
Stage in
*Time
(hh:mm)
Capacity
(mAh/ Ah)
Charge mode
Voltage (V)
Current (mA)
During
charging
Charging
current
Instantaneous
Battery voltage
Charging time Accumulated
elapsed capacity
Full stage
Trickle
charging
current
Different operating modes
24
25
Table 5. Various displays in Discharge Mode
Table 6. Various displays in Refresh Mode
Various displays (toggled by pressing DISPLAY key)
Various displays (toggled by pressing DISPLAY key)
Stage in
Discharge mode
Stage in Refresh
mode
Capacity
Capacity
Voltage (V)
Current (mA)
*Time (hh:mm)
Voltage (V)
Current (mA)
*Time (hh:mm)
(mAh/ Ah)
(mAh/ Ah)
During
discharging
Discharging
current
Discharging time Capacity during
During
discharging
processes
Instantaneous
Battery voltage
Discharging
current
Discharging time Capacity during
elapsed
discharging
elapsed
discharging
Instantaneous
During charging
Full stage
Battery voltage Charging current
Capacity
determined in last
time discharging
Maximum battery
capacity
Charging time
elapsed
Accumulated
capacity
During charging
processes
Instantaneous
Battery voltage
Charging time
elapsed
Charging current
Trickle charging
current
Instantaneous
Battery voltage
Trickle charging Elapsed time of
Full stage
current
last discharging
determined in
discharging
26
27
Note:
Table 7. Various displays in Test Mode
*The timer will be resumed and counted from 00:00 again after the time elapsed is
longer than 20 hours. (For example, 1:45 will be shown after the battery has been
refreshed for 21 hr and 45 min.)
Various displays (toggled by pressing DISPLAY key)
Stage in Test
mode
Capacity
(mAh/ Ah)
Voltage (V)
Current (mA)
*Time (hh:mm)
In case the power source is shortly interrupted or terminated when the charger is being
operated, the operational mode will automatically be set to “Charge mode at 200 mA”
to charge up the battery once the power source is back to normal, regardless the
operating mode (Charge, Discharge, Refresh or Test) which has been selected by user
before.
Charging time
elapsed
During charging
Charging current
“--- mAh”
“--- mAh”
During
discharging
Discharging
current
Discharging time
elapsed
Capacity of the
battery
determined in
discharging
Capacity of the
battery
Instantaneous
Battery voltage
During 2nd
charging
2nd charging
time elapsed
Charging current
Trickle charging Discharging time
Full stage
current
elapsed
determined in
discharging
28
29
The AA battery used with the
Size C adapter
The AA battery used with the Size D
adapter (it is required to place the
battery into the “C” adapter first
and then the “D” adapter)
2.
Ensure the polarity is correct and the assembling condition is good.
THE SIZE C AND SIZE D BATTERY ADAPTERS (FREE ACCESSORY)
The battery adapters are used for connecting the AA battery to devices requiring Size C or D
batteries. To apply the adapter:
Note:
User shall stop using the adaptor when there are any cracks or damages observed in
the adaptor, and in case undesired smell comes out while applying the adapter in
certain kinds of battery operated devices.
1.
Install the AA battery into the Size C or Size D adapter as below.
CARE AND MAINTENANCE:
Extreme temperatures, vibration and shock should be avoided as these may cause
damage to the unit
When cleaning the displays and casings, use a soft damp cloth only. Do not wet the
exposed metal part of the charging unit. Do not use solvents or scouring agents as they
may mark the LCD and casing.
Do not spill water to the charging unit.
Do not make any repair attempts to the units. Return it to its original point of purchase
30
31
for repair by a qualified engineer. Opening and tampering with the units may invalidate
its guarantee.
This product is only designed to be used by people who have read and understood this
instruction manual.
Do not expose the unit to extreme and sudden temperature changes, this may lead to
damage to the electronic parts in the unit.
The specifications of this product may change without prior notice.
This product is not a toy. Keep out of the reach of children.
No part of this manual may be reproduced without written consent of the manufacturer.
SPECIFICATIONS:
Input voltage for AC/DC adapter
:
:
100-240 VAC but MUST have the proper
adapter. Twisting prongs on a/c cord will only
damage the unit.
WARRANTY INFORMATION
La Crosse Technology, Ltd provides a 1-year limited warranty on this product against
manufacturing defects in materials and workmanship.
Charging current range
200 mA - 1800 mA
Max charging capacity
(capacity of rechargeable batteries)
Dimensions (H x W x D)
This limited warranty begins on the original date of purchase, is valid only on products
purchased and used in North America and only to the original purchaser of this product. To
receive warranty service, the purchaser must contact La Crosse Technology, Ltd for problem
determination and service procedures. Warranty service can only be performed by a La
Crosse Technology, Ltd authorized service center. The original dated bill of sale must be
presented upon request as proof of purchase to La Crosse Technology, Ltd or La Crosse
Technology, Ltd’s authorized service center.
:
:
3000 mAh
5 x 3 x 1.5” (129 x 75 x 37.2 mm)
LIABILITY DISCLAIMER:
The manufacturer and supplier cannot accept any responsibility for any improper or
incorrect use and any consequences occur.
Any performance of repairs or alternations by someone other than the original supplier
will invalidate the warranty.
La Crosse Technology, Ltd will repair or replace this product, at our option and at no charge as
stipulated herein, with new or reconditioned parts or products if found to be defective during
32
33
the limited warranty period specified above. All replaced parts and products become the
property of La Crosse Technology, Ltd and must be returned to La Crosse Technology, Ltd.
Replacement parts and products assume the remaining original warranty, or ninety (90) days,
whichever is longer. La Crosse Technology, Ltd will pay all expenses for labor and materials
for all repairs covered by this warranty. If necessary repairs are not covered by this warranty,
or if a product is examined which is not in need or repair, you will be charged for the repairs or
examination. The owner must pay any shipping charges incurred in getting your La Crosse
Technology, Ltd product to a La Crosse Technology, Ltd authorized service center. La Crosse
Technology, Ltd will pay ground return shipping charges to the owner of the product to a USA
address only.
interference. This warranty covers only actual defects within the product itself, and does not
cover the cost of installation or removal from a fixed installation, normal set-up or adjustments,
claims based on misrepresentation by the seller or performance variations resulting from
installation-related circumstances.
LA CROSSE TECHNOLOGY, LTD WILL NOT ASSUME LIABILITY FOR INCIDENTAL,
CONSEQUENTIAL, PUNITIVE, OR OTHER SIMILAR DAMAGES ASSOCIATED WITH THE
OPERATION OR MALFUNCTION OF THIS PRODUCT. THIS PRODUCT IS NOT TO BE
USED FOR MEDICAL PURPOSES OR FOR PUBLIC INFORMATION. THIS PRODUCT IS
NOT A TOY. KEEP OUT OF CHILDREN’S REACH.
Your La Crosse Technology, Ltd warranty covers all defects in material and workmanship with
the following specified exceptions: (1) damage caused by accident, unreasonable use or
neglect (including the lack of reasonable and necessary maintenance); (2) damage occurring
during shipment (claims must be presented to the carrier); (3) damage to, or deterioration of,
any accessory or decorative surface; (4) damage resulting from failure to follow instructions
contained in your owner’s manual; (5) damage resulting from the performance of repairs or
alterations by someone other than an authorized La Crosse Technology, Ltd authorized
service center; (6) units used for other than home use (7) applications and uses that this
product was not intended or (8) the products inability to receive a signal due to any source of
This warranty gives you specific legal rights. You may also have other rights specific to your
State. Some States do no allow the exclusion of consequential or incidental damages
therefore the above exclusion of limitation may not apply to you.
For warranty work, technical support, or information contact:
La Crosse Technology, Ltd
2809 Losey Blvd. S.
La Crosse, WI 54601
Phone: 608.782.1610
34
35
Fax: 608.796.1020
e-mail: [email protected]
(warranty work)
Quick Start for charging battery
Place battery in charger, plug it in, and let it sit for 10 hours.
(information on other products)
Note:
web:
The charger has many features like “conditioning” batteries which means discharging and
charging. It is not recommended to condition batteries until after they have been charged and
used 10 times.
Question? Instructions? Please visit:
Overview of Using Modes and Current Options
***Follow these steps left to right
Steps Plug in Place
batteries in mode…
charger
Select
Select Display To change To Change
Charge Blinks or mode
during
amount of
charge or
Hold for 5-10 to select
seconds to
activate
current
level
charging
current repeat
all steps from
beginning
36
37
notes
Select:
Charge
Discharge
Refresh
Test
Current Indicate Press de
How do you check battery condition?
200 to no
MODE key
(for all) or
Mode—test charge…
1000,
varies
by
more
chance NUMBER
to
Display—Use battery rating…re-chargeable never go whole way so for Voltage check for a
1.5 you are looking at 1.2 to 1.4 For capacity on 2400 looking for about 1900 to 2100 (first
time the capacity will be less like about 1700 to 1800).
key then
number change MODE key
and
for
type
individual
battery
You have 4
seconds
Why after I charge the battery to Full, remove, and test is not longer says
Full?
You have 8 seconds to
select mode
You
have 4
seconds
When you replace a charged battery it goes to trickle, and it can take from 1 to several hours
to get back to a full charge depending on the condition of your battery.
What is the charger capacity?
Maximum charging capacity is 3000 mAh
If you must switch batteries in your product before they die what mode
would you use to charge?
--Refresh and charge…if you have several days
--in a hurry just regular charge mode
My batteries are getting warm.
It is common for batteries to get warm will charging. The charger has a built in temperature
sensor which will stop the charging cycle if it has become too hot. Charging may resume
38
39
when the battery has cooled.
You may want to invest in a small charger/holder that will bring the battery back above .9v
when attached for 20-30 seconds. The battery can then be charged in our charger.
Allow batteries to cool before placing into a product to be used.
I cannot change modes.
Why do my new batteries not show full capacity?
Within 8 seconds of installing a battery, press and hold the MODE button for 5-10 seconds to
change modes.
Due to storage and shipping times, you should charge your batteries fresh out of the package.
All rechargeable batteries need to be used in a product “under load”, then charged, used,
charged, at least 5 times or more to reach full capacity. Batteries sitting in storage may lose
some charge over time.
Why does my display flash a number?
Your station will flash when first plugged in. If it continues to flash your a/c cord may be
defective.
It is not recommended to “condition” batteries until after they have been charged and used 10
times.
What type of batteries can I charge?
NiMH (Nickel Metal Hydride) or NiCd (Nickel Cadium) rechargeable batteries only may be
used in this product. Charging other types of batteries may result in failure of the charger.
As you use your batteries they will gain greater capacity and last longer. It is common for
your batteries to run down quickly at first.
My battery reads “Null”.
This charger requires at least .9v in the battery in order to charge it. If the battery is depleted
below that point, you will not be able to charge it on this battery charger.
Storing batteries
Store between 40 and 80 degrees F. Do not refrigerate.
40
41
Batteries will self-discharge if left unused. If unused for 30-60 days they may completely
deplete of power after long storage.
All trademarks and patents are acknowledged.
NiMh batteries should be stored fully charged and recharged every 30 days to keep in peak
capacity.
NiCd batteries should be stored fully discharged.
Do not “store” batteries in the charger.
How do you charge the smaller AAA battery?
Just place it in the smaller tabs in the charger.
All rights reserved. This handbook must not be reproduced in any form, even in excerpts, or
duplicated or processed using electronic, mechanical or chemical procedures without written
permission of the publisher.
This handbook may contain mistakes and printing errors. The information in this handbook is
regularly checked and corrections made in the next issue. We accept no liability for technical
mistakes or printing errors, or their consequences.
42
43
|